December 28, 2021 – A family-owned small business, Jammin’ J Automotive displays first hand-experience in delivering quality auto repair services. The company has grown massively over the past couple of years, with fast-growing popularity in St. Louis.
Finding a reputable auto repair company is much easier thanks to the internet. There are a few factors that one can look into behind taking over the car for its routine check-up or repair. Firstly, a good repair shop needs to have qualified technicians. At Jammin’ J Automotive, they look over the vehicle, photograph potential problem areas, and make this available to the customer almost instantly as the check is completed.
Trustworthy repair company’s services are both affordable and comprehensive. This is why Jammin’ J Automotive keeps its prices economical while offering one-on-one service to partner with its clients t get them the best deal possible. The company offers brake service, car fluid flush, auto suspension repair, power steering repair shop, tune-up, alignment, and custom car exhaust.
Jammin’ J Automotive has used a strategic system of communicating the health of customers’ vehicles with them to become the customer’s long-term vehicle service provider. This helps the company plan for the vehicle’s next needed service preventing an emergency.
“Our system also automatically schedules your next oil maintenance service based upon your vehicle history and will text you a reminder days before your appointment. This service has made our loyal customers very happy”, says a spokesperson for Jammin’ J Automotive.
(AB Digital via COMTEX) -- St. Louis’s car repair company Jammin' J Automotive serves the residents with prompt and efficient services. As a family-owned small business, they understand firsthand the challenge of surviving in this economy. Hence, their affordable prices come with the customer’s best interest at heart.
“No Fooling! There is no better time than now to schedule that bigger repair you have been putting off. No interest for up to 12 months on repairs over $480, plus you may even get 10% of your purchases back on a VISA gift card! If you want to see if you qualify, call Doug at 314.423.3876 or see the online link in the comments to apply online”, says a spokesperson for Jammin' J Automotive.
Jammin' J Automotive specializes in the diagnosis and repair of braking problems including pads, rotors, calipers, hoses, master cylinders, brake fluid flushes, auto suspension repair, power steering repair shop, tune-up, alignment, custom car exhaust services, etc. With its comprehensive free vehicle check, the company releases an instant online review of the vehicle, including photographs, recommendations, and one-on-one service. By partnering with the client, they can get the most from their dollar and the vehicle.
Jammin' J Automotive's unique ‘know before you buy service, gives the client a 35-point check-up. This information will include all the good, bad and ugly points of a new car. Now clients can get a comprehensive checkup before investing thousands of dollars. Some of its other services include stock exhaust solutions and repair. As a registered Magnaflow and Flowmaster Dealer, Jammin' J Automotive can create customized parts for any type of vehicle.
“Here at Jammin' J Auto & Tire, we try our best to be the best! Our technicians look over your vehicle and photograph potential problem areas and make this available to you, the customer, almost instantly as the check is completed. Our system also automatically schedules your next oil maintenance service based upon your vehicle history and will text you a reminder days before your appointment. This service has made our loyal customers very happy”, says a spokesperson for Jammin' J Automotive.
At Jammin’ J Auto & Tire, we think it is important to not only fix your vehicle the right way at a fair price, but we put a lot of emphasis and effort into educating our customers. As the Automotive Experts, it is our job to keep you in the know when it comes to the Repair and Maintenance needs of your vehicle. When you can understand how things are working with your vehicle, it makes it easier to understand the processes we use and the need for certain recommended services.
We take this issue so seriously that we have dedicated an entire wall in our lobby just to have examples ready of most common mechanical failures and many times we will have the failed part from your vehicle available to show you when the Repair is completed.
Anyone out there who has managed to find a good mechanic should consider themselves lucky as it is often times difficult to find honest skilled auto repair. With tons of repair shops and workers out there, how do you gauge whether the person you chose for your car is a skilled mechanic, or will you end up spending more than required?
To help tackle the dilemma of finding the right mechanic, below, we have outlined some of the basic questions that you should ask prior to allowing the mechanic to tune up your car.1. Have You Worked On This Model Before?
First off, you need to ask your mechanic whether they have worked on a model similar or your exact model. In their field, this is the best way to gauge the experience a particular individual has when dealing with cars and working on them. You don't want to hand out your car to someone who's going to play the guessing game. Some tasks, such as auto suspension repair, etc., are intricate jobs that only experienced professionals will be able to accurately repair.2. What Is The Diagnostic Costs?
Custom car exhaust shops already cost a lot, so you need to make sure you don't spend much on the diagnosis. Often, unprofessional workers would rip you off when it comes to the diagnosing stage, so to avoid that, ask them how much it would cost you for the machine to gauge the problem with your car. This amount sometimes may be worked into the overall cost but if it is a big repair simply be sure you know the cost to diagnose.
It is quite easy to cause serious and expensive damage to a computer-controlled vehicle.
Please consult your owner’s manual because jumping vehicles has changed a lot in the last 20 years.
NEVER touch or remove the battery cables while the engine is running.
Battery Vapor is Explosive – Keep all sparks away from the Battery.
With the introduction of so much technology, it isn't easy to conceive what our future has in store. Consider this, in 1908, Ford Motors started rolling the first affordable automobile with two gears, and one had to check the fuel by dipping a stick inside the tank.
Hundred years later, and the introduction of self-driving cars in upon us, and literal ones at that. Recently, Google and before that, Tesla have ventured into the self-driving models with varying degrees of success. Electric cars have become a near reality, and it's a matter of when rather than if that these will replace the gas vehicles.
Sure, when anyone looks at technology, one might see a lot of positives. Even with self-driving cars, the focus is to have a safer road experience. According to various researches, it is predicted that if the computers drive for humans, it will lead to a safer road environment.Benefits of Technology
Undoubtedly, the automobile sector has grown tremendously over the years, and thanks to the innovations, it has increased consumer safety and appeals to the customers. Here are some technologies that have revamped how drivers operate our vehicles.GPS – Global Positioning System
Long been thought of as a security risk to make it available for the masses, the decision to make GPS more accessible has been nothing short of life-changing. Gone are the days when one would have to navigate the busy streets and the open countryside with large paper maps. It has made driving more manageable as a driver may concentrate on the road while the GPS navigates every turn.
Please note that this advice does not take the place of taking any used vehicle to a trusted repair shop and having the vehicle physically inspected by an experienced Automotive Technician. Whether the vehicle is being offered for sale through a dealership or a private party.. The goal is to keep a customer from buying someone else’s problem. If a prospective seller will not allow a vehicle to be taken to an independent mechanic, it is time to walk away from the vehicle and move to the next one.Paint: Is the paint color consistent between body panels or is there a slight difference in color? If a body shop is going to paint only part of a vehicle, they will use a body gap (the small space between doors) as a stopping spot. Are color and texture consistent from one door to the next, or fender and hood? When the vehicle was painted at the factory the whole thing was sprayed all at one time and you can see the texture in the paint. If portions of the car have been re-painted it is difficult to match the original texture. Look closely at any reflections in the paint and see if it changes as you move around the car. Sometimes instead of a smooth glossy texture, there will be a slight ripple like the peel of an orange.Size of Body Gaps: When the car was new all the spaces between the doors, hood, and trunk were the same distance apart. If body gap spaces seem different or change, the car has probably suffered an impact. A minor fender bender might be ok but if the car has severe differences it can be a warning sign that there may be frame damage, which will need to be reviewed with the vehicle on a lift.Pop the Hood: Is the engine area clean or dirty? A super clean engine compartment and could have been sprayed with some sort of shiny stuff to make it look newer. This may be a cause for concern. If an engine of a used vehicle is extraordinarily clean, it can be because the engine has been power washed to remove signs of leaks. These leaks will start again after the purchase of the vehicle and the new owner gets a mess on the garage floor. Slowly looking around the engine compartment, observing things that look loose, hanging, or out of place. Look for wetness on the side or bottom of the engine, as well as noticing any puddles underneath on the ground. Look for rodent/squirrel droppings or any grouping of grass or nesting material in the engine compartment. Animals can do a lot of damage to wires and this happens more frequently than one would think; even in suburban areas. Make notes of anything that seems out of place.Seating Areas: If possible, take a friend along and ask them to sit in each seat and play with everything including the radio, windows, and power seats. For SUVs and vehicles with a DVD player, bring a DVD along to test accessories. Pay special attention to the blower fan that moves the air out of your vents, does it work on all speeds and does it blow out the proper places when directed there? Does the right temperature come out on A/C and heat? If the vehicle has a rear vents, have your helper sit in the back to check those. HVAC can be expensive to fix, especially if the whole dashboard has to come off for the repair.Test Drive: Is the steering wheel pointed straight when the car is driving straight or is it trying to drift away? Try to drive at lower speeds and on the highway. Listen and feel for any vibrations or odd noises when turning, braking, or driving. Use brakes smoothly and once or twice try a sudden stop.Tires: It is possible to get an idea if the tires will need to be replaced right away. Place the edge of a penny, headfirst, in the tread gaps in several places around the tire. If Lincoln’s hair is covered by tread, there is still some life left in the tires. If most of his head and hair are visible, the tires most likely need to be replaced. View the tread across the width of the tire and notice if one side of the tire looks more worn down than the other. Uneven wear can be caused by broken or bent suspension parts and misalignment. If the vehicle needs additional repairs, that should be factored into the asking price. Try to find the DOT number on the tire sidewall and look at the surface of the tire. The last 4 digits are typically the month/year of manufacture of the tire. Tires manufactured more than 5 years ago or ones with excessive dry, cracked areas can be suspect even if they have a lot of tread left.
Look at the attached picture, first, observe the body gap and notice how it gets tighter as it goes towards the red taillight. Next, notice the difference between the upper and lower panels, see how the top part of the reflection is glossy and the lower part is dull. This vehicle has been repainted with the same color but the texture of the paint near the top is crinkly, which resembles an orange peel. This may show that some body work has been completed on this vehicle.
If you are in St. Louis, MO it is highly recommended to bring the car in for a full review before purchase! There is not a replacement for putting a vehicle on a professional lift and having a trained technician look it over. Doing so, can help make a used vehicle purchase a positive experience. Visit us at jamminjauto.com or Call us today at 314.423.3876 to schedule a pre-purchase checkout!
If you ask about who is the leading auto repair company in St. Louis, the answer would definitely be Jammin J St. Louis Auto Repair, a small family owned business that is rapidly growing. They offer a variety of services for car owners who are willing to upgrade, repair and replace everything related to their car.
Although they offer more than 10 services, custom exhausts are one of their specialties. In this article, we will talk about exhaust systems, its functions and all the types of custom exhaust available at Jammin J Auto..Functions of the exhaust system.
Exhaust system has many functions that add to both to the beauty and the smooth operation of a car or truck. Primarily, the exhaust system contributes to the quietness of the engine and conceals and muffles the sound of the gasses that comes out from cylinder heads. Not only this, it is also the mechanical part that sucks the exhaust gasses and transmits them to the rear of the car, through this operation, the gasses and toxic fumes are prevented from leaking to the passenger compartment through the vents. Jammin J St. Louis Auto Repair have a vast knowledge about exhaust systems they understand the importance of a custom exhaust.Types of Custom Exhaust
The most used exhaust systems often have one single exit pipe. They are often found on cars that are purchased directly from dealers. Even though they are not very cheap, they not very efficient. The cost of installing and manufacture are low which makes them the most commonly used. Luckily, exhaust systems can be upgraded.
An exhaust system is composed of several part, each has its own function damage to any one part can affect the overall performance of the system. At Jammin J St. Louis Auto Repair we have your best interest in mind, that is why we will offer you exhaust guidance and recommend the best types of custom exhausts to go with and here are a few:
Prepping Your Car For The Upcoming Winter With Jammin’ J Auto
Winter can be an extremely testing time for cars and drivers alike. A lot of common winter-specific problems, such as frozen doors, dead batteries, corrosion caused by increased humidity, lower air pressure in your tires, unresponsive spark plugs, etc., are forgotten about throughout the rest of the year.
Therefore, preparing your car in advance for the winter months can save you money and a great deal of grief. Thankfully, here at Jammin’ J Auto, St. Louis’ premiere Auto Suspension & Power Steering repair shop, we can take care of your vehicle’s pre-winter tune-up and save you money at the same time.
Our team of expert techs can take a quick look at your car, and in a matter of minutes come up with a list of issues that, if taken care of in advance of the winter months, will make your life easier.
By failing to prepare, you are preparing to fail, so take a look at the list below and prep your car for this upcoming winter.
Knowing how your car’s exhaust system works can actually help you attain maximum performance while helping to maintain your vehicle in top shape over the years.
So, let’s talk about what an exhaust system is, what it does, and how an exhaust tune-up from a professional repair shop can save you money down the line.
First Things First - What Is Exhaust?
The exhaust system is a crucial element of your car’s overall performance. Your car’s exhaust system is the set of components that allow the engine’s combustion byproduct gases to be funneled outwards and vented into the environment. The exhaust system is particularly important to your vehicle’s operation for two reasons:
If the byproduct of the engine’s combustion reaction is vented quickly, the engine gains more power because the cylinders clear out more efficiently after each combustion cycle. However, if improperly tuned, this can lead to overheating and a higher rate of fuel consumption. If the engine’s combustion byproducts are not vented properly, there won’t be sufficient room for fresh air to mix with the gas and the engine will lose power as well as fuel efficiency
No matter what season it is now, if you live in St. Louis we all know it is cold one day, hot the next and if it isn’t leaves, it is flowers or gumballs – always something falling on your vehicle. I wanted to touch base with you on a problem we see that can damage vehicles that no one really spends much time thinking about.
All of our vehicles are designed with paths for the water from rain to flow from the top of your car, through the gaps and down, to the bottom of your car. These gaps are specially designed to do this and they are very important in keeping your engine and all the very costly electronics from getting soaked every time it rains! So look at your trunk next time you walk by your car and look where water would go if it goes in the gap at the front of the trunk lid and you will see a channel that guides the water down each side of the trunk opening and out the bottom usually around the tail lights. Is there debris there? Sometimes we find a small collection of leaves, or blooms from your trees, or even pine needles. If the answer is yes, take a minute and remove the leaf and tree dropping sludge before it clogs the pathway and backs up into your trunk.
There are also drains under your hood that direct the water that come down the windshield through some plastic screens and usually out the lower front fender. These screens we usually see clogged up especially in the fall when the leaves are coming down but also in the spring and summer when we see other debris falling from trees or animals that live in the trees above our vehicles.
It is indisputable that the brake system is one of the most critical safety systems, if not the most important, of all of the integral systems in a motor vehicle. Brakes are essential to user integrity and safety and are the primary means of protection that we have on the road when we go behind the wheel of a car.
The brake system helps us to slow down and stop the vehicle. Therefore, the brake system has to work effectively and efficiently. Its operation must be precise, and its maintenance must be prioritized above all things. Otherwise, we run the risk of experiencing premature deterioration of the system, and we run the risk of getting into a potentially life-threatening accident. For the brake system to always work correctly, it is necessary to keep all of its components in perfect condition. In fact, with each braking, heat and friction cause the components to suffer from wear and tear. As such, in order to not impair the proper functioning of the system as a whole, at some point, the discs and brakes must be replaced altogether.
Drums and Discs There are two primary types of brake systems: Drum and Disc.Drum Brakes: Drum brakes are located on the wheel itself and, for the most part, found on vehicles from the '60s and 70s, since the more efficient disc system replaced them. However, plenty of cars on the road still use Drum brake technology. The main problem with drum brake systems is that they have a rather reduced cooling capacity. In other words, they can quickly overheat. Additionally, their maintenance and assembly are far more complex than in the case of disc brakes. Drum brake systems provide great braking power. It requires less effort on the pedal, but it implies a greater risk of locking, despite their high efficiency. Drum systems are very durable; however, it is recommended that they are serviced regularly.
Disc Brakes: Brake systems that utilize disc components can be mounted on the interior or exterior of the wheels. They can also be placed on any axle shaft and have a smaller friction surface; this provides them with a more efficient cooling capacity than drum-based systems. Disc brakes possess a more gradual braking speed, which makes them more effective overall. However, disc brakes erode far more quickly than drum brakes and are very sensitive to moisture and grime. As a result, disc brakes are more susceptible to deformations, cracking, and rust. It is extremely important that disc brakes are serviced regularly, and in comparison, to drum brakes, disc brake pads need to be replaced more frequently.
So, if you notice that your brakes are making a weird noise, or you feel a distinct pulse when you brake, swing on by Jammin' J Auto & Tire to get a detailed analysis and professional service.
Let's talk about air conditioning. Most of us in St. Louis don't give our air conditioning a second thought as long as it works when we turn it on. But it's a complex and expensive system that we should spend time thinking about before it starts blowing hot air. The air conditioning system in your vehicle performs four basic functions: cooling, dehumidifying, cleaning and circulation of the air in the vehicle. As the refrigerant goes through all of the four phases of compression, condensation, expansion, and vaporization it goes through its own changes. During the condensation phase, heat transfers out of it and into the surrounding air and it expands, then when it evaporates, it absorbs heat to cool the air in the surrounding area. As the refrigerant runs through all of the phases of the cycle, it goes from liquid to vapor and then back to liquid and so on.
The main parts of the system are the refrigerant, the compressor, a condenser, an evaporator, a receiver-drier, blower and some switches and valves and an array of cooling lines and hoses. The compressor normally has some sort of magnetic clutch as well. The compressor in an AC system has special oil that is used to lubricate the compressor and the entire system. It actually mixes with the refrigerant and travels through the whole cycle to keep everything running. You may hear some of these parts named when you bring a vehicle in for AC service. If this oil leaks out with your refrigerant, your air conditioner may still make cold air, but the parts don't have enough oil to protect them and they wear out faster than they should or things may start to clog up the tiny areas that the vapor has to travel. So it's important to service the air conditioner as recommended by your service center. Even with regular service, A/C parts can just wear out. Normal wear and tear eventually gets to all moving parts. Addressing early problems can save on more extensive repairs down the road. For instance, a common failure is the clutch that turns the compressor on and off. If you can take care of a bad AC Clutch when it first starts having problems, you may be able to save the compressor. Wait too long and you'll have to replace both.
Sometimes, when you first use the system at the beginning of the warm months, you may notice right away that things do not seem cool; but air is blowing, so it is hard to know for sure what is going on. Bring your vehicle to us and we will visually inspect the system for leaks and/or damaged parts, then fill the system with fresh refrigerant mixed with a dye that shows under ultraviolet light. The dye will mark any connections that might have suffered damage and are leaking and we can pinpoint the problem with greater accuracy to facilitate the best solution moving forward. Give our service advisor at Jammin' J Automotive a call for recommendations or to schedule an AC inspection, especially if you are hearing strange sounds when your air conditioning turns on, or even if it just isn't as cold as it used to be.
Let me start off by telling you the old way of replacing Transmission Fluid and then the new…
We used to and sometimes still do (for leaking pan gasket) a transmission filter and pan drop. We take the oil pan off the unit and replace the filter and then put it back together including a new gasket for the pan. The problem is that you usually only get 3 or 4 quarts of the old fluid out and some transmissions can hold 15 or more so you were not replacing the majority of the fluid.
Today we do a full Transmission Fluid Exchange or commonly known as a Transmission Flush. 1st a chemical cleaner known as BG Quick Clean that dissolves the varnishes that get baked onto transmission parts is poured in and driven to get the heat activated cleaner working. Then a Fluid Exchange machine (pictured below) is hooked up to the transmission cooler lines. This machine is literally like a dialysis machine for humans, it removes the old fluid while cycling in the new, it also cycles through 16 quarts as an over flush to make sure all of the cleaning fluid is removed.
Why is this important? Transmission fluid, just like motor oil, breaks down; the fluid is subject to very high heat which wears it out. As worn fluid is pumped through the unit, parts wear quicker especially the clutch disc (pictured below). If you notice in the picture there is a steel disc and a friction disc stacked every other one. The friction material, which is designed to slip and not slip at certain times, relies on this transmission fluid being clean. When you allow that fluid to go too long without ever having an exchange, the debris in the fluid will literally wear the friction material off the friction disc. Then if you do the flush too late, you replace the gritty old fluid with clean new fluid and then the car will not move because all the friction material went out with the old fluid.
The solution, is to not wait too long, have the Transmission Fluid exchanged every 36 - 50,000 miles. This service includes…
The big debate on oil changes is how often do I change my oil: 3,000 miles? 5,000 miles? 7,500 miles or even more? Back in the day the recommended mileage interval was every 3,000 miles and/or 3 months. Today vehicle manufacturers are pushing back the intervals to 5K and some are going as far as 10K with the advertisement of vehicles with low maintenance costs. But, is it really OK for the engine to go that long without the oil being changed?
As the engine runs and burns fuel it produces carbon, acids and water. These wastes when blended with the oil form sludge. Sludge buildup can get so bad that it will start to restrict the flow of oil and even clog the oil passages, which in turn can starve the engine of oil lubrication. This can be made worse by lots of short trips where the engine temperature does not get hot enough to evaporate the humidity that builds up inside the engine. Engine damage may range from a noisy start up to broken timing belts and even engines locking up and becoming boat anchors.
As oil breaks down it loses its viscosity (becomes thinner) and your engine is designed to run at a specific viscosity and the longer you run the oil the more it breaks down. So back to what the manufacturers recommend; understand that their goal is to get your vehicle out of the warranty period and they are confident that your engine will survive several 7,500 mile oil changes during the warranty period. After that your engine is fixed on your dollar, not theirs.
Below are pictures of a customer’s engine that was in for an oil leak. We found that the oil was having such a hard time returning to the oil pan because of sludge buildup that it was building up in the valve cover and eventually caused an oil leak because it had nowhere to go. This is the type of sludge problems that come from not changing the oil on a regular basis!
The more often you change your oil the better, here at Jammin J Automotive we recommend 3,000 mile or 3 months whichever comes first. We also recommend and use a product known as BG Motor Oil Additive (MOA) which is a cleaner and friction reducer. The MOA impregnates the engine components at the molecular level and helps extend the life of the oil. With MOA we recommend 5,000 miles or 4 months. Once again, the more you change your oil the better. Our commitment to you and your vehicle is for the life of the vehicle, not just the warranty period.
Brake fluid attracts moisture, over time moisture creeps into the brake hydraulic system and can cause serious problems (especially on today's cars with anti-lock brakes). What happens is the moisture gets into the system and not only causes rust and corrosion in the lines, but it can also reduce the boiling point of the brake fluid and this can cause the fluid to boil inside the caliper causing brake fade.
We had a customer come in for the typical brake job (pads & rotors) and upon the test drive the vehicle pulled to the left and we could tell that something was not right. After checking the calipers for sticking in their slides we eventually found contamination in the brake hydraulic system. When the caliper pistons pushed back in, it literally stirred up the dirt and sediment inside the caliper which kept the pistons from moving freely. The pictures below is of the inside of the brake system and the piston, showing the debris that had accumulated inside the lines causing the problem.
Another repair we make on a regular basis is the replacement of steel brake lines, some of which are rusted and broken from the inside. A brake fluid flush keeps new fluid in the system and greatly decreases the lines from rusting from within and removes debris.
On this picture, you are seeing a rubber plug that has been crammed into the side wall of a tire. There is so many things wrong with this that I don’t know where to start, but I’ll attempt to hit the high (or low) points.
#1 At Jammin’ J Automotive, we will not install a plug on a passenger car tire, it's not a good fix for any tire! (A tire plug is a very tough piece of rubber, coated with glue, and stuffed into the tire injury and everyone just hopes it will hold)
We have had customers come in wanting us to do what we call a pad slap. A pad slap is when you just put new brake pads on and do nothing to resurface the rotor surface. When I get asked to do a pad slap I always hear my Automotive Tech School instructor’s voice in my head saying “Never, never, never put new pads on an old rotor surface!” While a pad slap is, in theory, cheap and fast, you are doing your car and yourself wrong.
A used rotor surface has a mirror like finish that you won’t see on a new rotor. When you put new pads on an old glazed rotor you are messing with the friction coefficient that is designed to stop the car in all situations.Sometimes customers come in and their brake pads look great as far as thickness, but they are saying that they have a vibration when braking, especially on the highway. What has happened is the brake rotor over time has been exposed to excessive heat and cold, which causes the rotor to warp and they are feeling this as a shake/vibration when braking. Rotors must either be replaced or machined when pads are replaced.
We first measure the old rotors to make sure there is enough material to be machined (cut) off so that the rotor does not go below the minimum thickness specification. At Jammin J Automotive we have a Procut On Car Brake Lathe, which will do what is called Machine Matching of the brake rotors. The Procut Machine machines the rotor while still on the vehicle and literally matches it to the wheel bearing and hub; the result is a beautiful new braking surface which is balanced to the vehicles rotating parts associated with that wheel’s braking system which equals safe and very smooth braking. When we purchased the machine we were told by the technician that even new rotors should be machined and we thought he was crazy. After measuring and testing new rotors over the course of several weeks, we were shocked at how many needed resurfacing (all of them!) to correct for inconsistencies in the rotor’s surface and now we Machine Match all new and existing brake rotors to ensure the best braking performance possible on every brake service we perform. To view what this process actually looks like, click here to view a video.
Here are some pictures of a customer's rotors who wanted just pads only, showing both sides of the rotor. While the side of the rotor that was visible through the wheel doesn’t look so bad, the back side clearly has extensive rust and very severe grooves that are just too deep to machine out of the rotor.